WWA Info Exchange

For Woodworkers By Woodworkers
It is currently Tue Mar 19, 2024 5:26 am

All times are UTC - 5 hours




Post new topic Reply to topic  [ 32 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Galloper carriage
PostPosted: Sat Feb 10, 2018 8:23 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
I was contacted by the Texas Historical Commission to build a cannon carriage for a Verbruggen cannon barrel that they have ordered from South Bend Replicas.

I don't have much to go on other than these two pictures of a replica carriage someone made that I found on the internet.
I also have a simple drawing from the 18th century ordnance text by John Muller, A Treatise of Artillery.
It has some hard to follow measurements in it.

So a lot of this design is made up by me.

The Verbruggen barrel is in the process of being cast. It will be 37" long and weigh 200 lbs.
It will have a 2 1/4" bore.
I probably won't see it for at least 4 months. So this will be a thread in progress.

I have ordered 50", twelve spoke wheels for the carriage. It will be six weeks before I get them.

Here is what I have done so far.

Enjoy the pictures.

Replica cannon carriage made by someone else.
My carriage will not have the ammunition boxes on it. They want to be able to remove the barrel and cheeks and drop a wagon bed on the carriage which I will also be making.

Image

Image

Drawings from John Muller's book.

Image

Image

Image

Picking up the wood. 3" thick, 2 1/2" thick, and 2" thick oak.

Image

Ripping the 3" to size. My 3 HP Unisaw cut it well but didn't like the 10' cuts at all. The blade would get too hot and bog down throwing the breaker. All in all, I had to make 60' of cuts.

Image

I made the middle cut on the band saw.

Image

Image

Here I have the side rails sitting on the 5" X 5" axle housing that holds the 1 7/8" steel axle. I also have the three horizontal braces sitting on top. The axle sits 25" high like it will when it is on wheels.

Image

Image

Image

Image

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 10, 2018 8:28 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Mortise and tenon.
I don't know what joint to use here but this made the most sense.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image


That's all I have done so far. Stay tuned for more Zulu action shots. :shock:

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 10, 2018 8:36 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Those top two cross braces are 3" X 5" X 28" not counting the tenon.
The curved brace is 3" X 4" X 28".
The rails are 3" X 6" X 10' long.

I need to round the ends on these things and I'm not sure how I'm going to do it yet.
It's way to long and heavy to use the band saw. At 3" thick, I can't rough it out with a Skil saw and true it up with a sander. I would have to cut it from two sides. It would be too easy to mess it up.

I have a friend that says he can do it with his CNC wood carving machine but that seems like a lot of trouble.
Any ideas? I have to round over the front and back of the rails. Also the step in the middle.

Zulu

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 10, 2018 11:07 am 
Offline
Veteran

Joined: Sun Dec 19, 2004 1:01 am
Posts: 4044
Location: Rolling Meadows, IL. USA
I was confused at first i saw snow and y'all do not get snow.
But then i red that it was someone else's.

_________________
"It is not a mistake it is a learning experience"
Monte


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 10, 2018 11:17 am 
Offline
Veteran
User avatar

Joined: Thu May 29, 2003 12:01 am
Posts: 3483
Location: Sacramento, CA
Z -
The work you do never ceases to amaze me.
So much so that after so many fantastic builds such as these I find it hard to believe you don't have solutions to your issues. ;')

The step in the repro picture appears to be convex, while the step in Mullers diagram appears to be concave.
You could potentially use a large hole saw to cut this curve if all was supported and braced well.

However, I think the solution for the step as well as the ends is to make templates and route then using pattern routing bits.
These bits do come in lengthy shafts that should be able duplicate the pattern from both sides reaching 3" in total.
Taking multiple passes of course.

BTW I would highly suspect that mortise and tenon joints are "period correct".
I did find a few reference links that you've likely already seen ...
http://lib.jrshelby.com/verbruggen-online.htm
And the google images I see for "verbruggen cannon" has a much different looking carriage that what you have pictured.
Though I'm sure your research is more on point than my half cup of coffee effort this morning. ;) :D

_________________
~Dan.


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 10, 2018 11:46 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Dan,
The historian at the Texas Historical Commission came up with the carriage design.
I'm just the poor sap that gets to build it.
Actually, it's quite fun.
I never think I am working when I'm in my shop.
Zulu

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 10, 2018 6:12 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
I added the side cheeks that will actually hold the cannon today.
I can''t bore the trunnion pockets until I have the barrel.

I also figured out how to round the ends of the rails. A friend suggested I use the mitre saw and rotate the saw around the stationary rail cutting off a little at a time just outside my line. It worked great and was fast.
I then cleaned it up with a angle grinder and sanding disc.

Zulu

Image

Image

Image

Image

Image

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sun Feb 11, 2018 12:53 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
I got everything back together this morning.
I've gone as far as I can with the wood work until I get the wheels or the barrel.

It's looking pretty cool I think.
Now I start on the metal work.

This thing is a beast!
Zulu

Image

Image

Image

Image

Image

Image

Image

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sun Feb 11, 2018 6:22 pm 
Offline
Veteran

Joined: Sun Feb 21, 1999 1:01 am
Posts: 2777
Location: Rochester MN USA
ZULU: After looking at these pics, I have a question about the wheel/axle fitting. Is the axle fixed in place in the carriage or does it simply rotate with the wheels? If it is fixed in the carriage, are their bushings to keep it centered in the housing or if the axle is fixed to the wheels are there bearings in the housing for wear and stability?
I liked your “gitter done” solution to the radiused ends. McGuyver simple and effective! :thumbup:

_________________
Everything was new once.
newtooth 311
Rochester, MN


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sun Feb 11, 2018 9:59 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
newtooth wrote:
ZULU: After looking at these pics, I have a question about the wheel/axle fitting. Is the axle fixed in place in the carriage or does it simply rotate with the wheels? If it is fixed in the carriage, are their bushings to keep it centered in the housing or if the axle is fixed to the wheels are there bearings in the housing for wear and stability?
I liked your “gitter done” solution to the radiused ends. McGuyver simple and effective! :thumbup:



newtooth,
The axle will be fixed in the axle housing with bolts through the axle.
The wheel will have a bushing that accepts the 1 7/8" axle.
Thanks for the comment.
Zulu

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Thu Feb 15, 2018 10:27 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Got some metal work finished.
Here are some pictures.

Axle straps hold the wooden axle housing to the side rails.
Axle bands will wrap around the ends of the wooden axle housing for strength.

Image

Image

Image

Image


Started on the flat iron that will top the cheeks. Can't finish them until I have the barrel.

Image

Image


Handles and a sponge bucket hook.

Image

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Tue Feb 20, 2018 8:07 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Just adding a few pictures.

Added a cross bar at customer's request and installed the handles.

Image

Image

Image

Image


Making the skid plates out of 3" X 1/8" flat bar.

Image

Image

Image

Image

Image


Still waiting on wheels and the barrel. Could be a while yet.
I've started on the removable wagon bed. My customer wants to be able to remove the cannon barrel and mounting cheeks and install a wagon bed at times.

More pictures later.
Zulu

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Wed Feb 21, 2018 5:20 pm 
Offline
Veteran
User avatar

Joined: Sat Jan 14, 2006 10:44 am
Posts: 3951
Location: Skagit Co WA
I don't often comment on your photos, Zulu, but believe me, it's fascinating to watch your projects come into being. There's one picture that apparently shows your forge(?). Are the two pipes leading into the top gas jets? I've often thought I'd like to build a forge but don't really know how to go about it.

_________________
Nullum Gratuitum Prandium

Cheers - Dennis


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Wed Feb 21, 2018 9:24 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Hey Dennis,
Yes the two pipes feed propane in to the forge. So it has two burners. The propane tank is just out of the picture.
This is a horse shoe forge. Additionally, it has a small trap door in the back that allows me to put something long in there.
In this case, I was heating the middle of a 24" X 3" wide piece of flat bar.
Zulu

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Thu Feb 22, 2018 5:28 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
Making the cart and hinges.
I have made the cart bed that will sit on top of the carriage when the barrel and barrel mounting cheeks are removed. This will allow my customer to do double duty with the Galloper carriage.

Also some pics of how I made the hinges.
I still have to make a tailgate latching system of some sort. I will have to ponder that.
Also it has to come apart and be sanded and most of the bolts have to be shortened.

Zulu


Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

_________________
Zulu's website
http://www.jmelledge.com


Last edited by Zulu on Mon Oct 08, 2018 5:08 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sat Feb 24, 2018 7:21 am 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
The tailgate locking mechanism.
Zulu

Image

Image

Image

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Sun Mar 04, 2018 6:18 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
It's hard to tell if there is still anyone on this forum besides me.
It's pretty quite around here.

Tom, What are you working on?
Dennis, Where are you?
Larry? You pop in every now and then.
reelinron, you try a lot.
Gene?
Ron?
drstrip?
Mango, we can always count on you to say something.
The rest of you?

This forum is almost dead.
There is only one way we can fix it.

So!
I will bore you with some more pictures of the metal work on my carriage before cleaning and painting.
There is still a lot of metal work to be done.
Here is some of it.
Zulu

Image

Image

Image

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Mon Mar 05, 2018 1:52 pm 
Offline
Veteran
User avatar

Joined: Mon Apr 11, 2005 12:01 am
Posts: 4950
Location: Seattle, WA, USA
Hey Zulu,

Still here, mostly lurking. I'm still working on shaker boxes, learning what works and what doesn't. I've also tried a small number of finishing combinations, but mostly just plodding on. I'll have another post in a week or so.

Cheers,
Tom

_________________
"There is no path to peace, peace is the path."
Mohandas K. Ghandi
Image


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Mon Mar 05, 2018 6:06 pm 
Offline
Veteran

Joined: Thu Dec 31, 2009 2:48 pm
Posts: 1145
Location: Cypress, TX
tms wrote:
Hey Zulu,

Still here, mostly lurking. I'm still working on shaker boxes, learning what works and what doesn't. I've also tried a small number of finishing combinations, but mostly just plodding on. I'll have another post in a week or so.

Cheers,
Tom


Hi Tom,
If you are still working on shaker boxes, you must see a market for them.
Are you selling them?
Don't worry, they are out of my skill level but I do like to see what is selling or not.
Cannon stuff is still selling for me believe it or not.
Zulu

_________________
Zulu's website
http://www.jmelledge.com


Top
 Profile  
 
 Post subject: Re: Galloper carriage
PostPosted: Mon Mar 05, 2018 8:03 pm 
Offline
Veteran
User avatar

Joined: Mon Apr 11, 2005 12:01 am
Posts: 4950
Location: Seattle, WA, USA
Hey Zulu,

Actually, I'm still teaching myself to make shaker boxes. There is more to them than meets the eye, and I am enjoying the process. There is actually little to no market for them, and what market there is, is very cheap. So I don't plan to make them for profit. What I might do is teach a class in how to make them.

Cheers,
Tom

_________________
"There is no path to peace, peace is the path."
Mohandas K. Ghandi
Image


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 32 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group